Help Installting FreePBX
@IanChong wrote: I’m new to FreePBX. I was encouraged by an equipment supplier to try it out as it did not require significant hardware cost. So, I got an hp 255 G6 (AMD A6, 4GB RAM, 500GB HDD) and...
View ArticleRebuilding asterisk16 doesn't work
@robyf wrote: Hi, I’m following the instruction at Applying+patches+to+Asterisk+in+distro+SNG7 (sorry cannot post links yet) which was working up to v16.9 or 16.10, but today traying to rebuild v16.13...
View ArticleError after update to FreePBX 15
@jarvisswope wrote: I upgraded freepbx to 15 and when it rebooted i get stuck at the Dracut Emergency Shell See attached pictures. I have ran blkid and it shows the disks. System is down hellppppp...
View ArticleYum upgrade failed on distro
@tonyg wrote: hi, i am using distro 15. i patched not to long ago with no issues, but i went to patch again yesterday. and got these errors Error: Package: sangoma-pbx-2008-1.sng7.noarch (sng-pkgs)...
View ArticleSimple Question_New_Guy!
@quazimotto wrote: Greetings All, I have installed SNG7 and I cannot access the box with Terra-Term or WinSCP. It rejects my attempts. What linux command do I nee to issue? Quaz Posts: 3 Participants:...
View ArticleSangoma Distro 64bit 20008 - Cannot Save Storage configuration
@rastermus wrote: Hi, I’m trying to load Distro STABLE SNG7-PBX-64bit-2008-1. In the anaconda configuration screen I get the message “Cannot Save Storage Configuration” in the storage config section....
View ArticleUpdate Timeout
@thn80 wrote: If I try to upgrade my FreePBX 15.0.16.75 via automatic GUI updates or via the console I get the following error all the time: Could not retrieve mirrorlist...
View ArticleWhat have I done this time? RPM command Errored... now can't login
@MacsOffice wrote: I attempted to update and was met with RPM command errored, Delete /dev/shm/yumwrapper/* and try again. Exit code 1 - see FreePBX log for more info. I then attempted to log in using...
View ArticleDisplay is out of range
@peterthesing wrote: When I try to install my freshly burned sangoma dvd containing asterix and freepbx I got an error message on my monitor /display it is “out of range”. When I install opensuse 15.1...
View ArticleBroken Kernel Panic
@RichE wrote: FreePBX1.jpg4032×3024 3.34 MB For some strange reason which is beyong me, my FreePBX stopped working and when i reboot it i get a choice of two versions, if i leave it or select the top...
View ArticleFPBX 13 not booting to local drive
@mustachio wrote: Just spun up a new FreePBX 13 box, and every time i reboot it, even though it has been fully installed, it keeps returning to the installation GUI, and will not auto boot from the...
View ArticleYum update failing
@magnum406 wrote: I am typing yum clean all and then yum update. The detail of the failure follows: —> Package yaml-cpp.x86_64 1:0.5.1-2.el7 will be an update –> Running transaction check —>...
View ArticleSystem Updates Stuck in Loop [Errno 12] Timeout & yum lock
@bradm413 wrote: FreePBX 14.0.13.40 PBX Distro: 12.7.6-2002-2.sng7 Asterisk Version: 13.32.0 It’s been a while since I’ve seen any system updates available in the GUI Dashboard. Recently I saw a bunch...
View ArticleFreePBX 13 Updates (non-distro)
@staticsyphon wrote: Hello, I’m trying to update some modules on my older FreePBX install, but I’m getting a dependency error when trying to upgrade, e.g. sysadmin: ➜ ~ sudo yum install sysadmin...
View ArticleGraphical Interface
@vlinas wrote: Hello everyone, i have Asterisk 13.8.1 built by mockbuild @ jenkins2.schmoozecom.net on a x86_64 running Linux with Yealink ip phones registered on VLan from previous IT guy. Is there...
View ArticleNew Install of 2008-1 Distro Issues
@openpbx wrote: I have beeing trying to install the FreePBX distro on a spare computer and it always gets stuck for quite sometime on 625/729 which is kmod-dhadi-linux and then starts going again and...
View ArticlePetition to remove the check for updates on ssh login
@lgaetz wrote: https://issues.freepbx.org/browse/FREEPBX-21947 On the Distro, when you login via ssh, you get an immediate status screen indicating if there are pending updates. There is also a check...
View ArticleError: Trying to remove “sangoma-pbx”, which is protected
@able wrote: [root@freepbx ~]# yum update Loaded plugins: fastestmirror, versionlock Loading mirror speeds from cached hostfile Resolving Dependencies –> Running transaction check —> Package...
View ArticleSwappiness on FreePBX Distro
@AdHominem wrote: I run my FreePBX on a ESXi VM. For years, I’ve given it 2GB of RAM and it’s run just fine. After a recent upgrade earlier this year, I noticed that my machine would have some...
View ArticleIssue with Distro
@ilouiemiami wrote: Guys, I’ve tried installing the latest Distro downloaded from FreePBX onto a DigitalOcean Droplet, and while installing I was forced to add SSH Keys instead of a Password. My issue...
View Article